05905 / 94541-10
Kontakt
2K PUR Topcoat PLUS | HP-PP-TEXTUR (slip-proof)
HP-PP-TEXTUR | 2K PUR Topcoat (slip-proof)
HP-PP-TEXTUR is a high-quality two-component 2K PUR topcoat (containing solvent) for non-slip and weatherproof coatings.Ideally suited for textured finishes of boat and sport equipment, truck refinish, industry etc.
✔ brilliant colours
...for highest demands and long-lasting UV protection!!!
deliverable in nearly all RAL-colours
✔ very good resistance
...to weathering and to mechanical loads
✔ easy to apply
... by rolling and brushing.
For new coatings or renovations in combination with our epoxy resins.
properties and fields of application:
- deliverable in nearly all RAL colours
- results in a textured non-slip surface
- suitable for coating tank surfaces, boat and ship ceilings, surfboards, walking areas on industrial floors or in swimming pools, etc.
- good resistance to water and chemicals (if the dosage regulations for the chemicals used for swimming pool hygiene are observed)
- long-lasting colour stability
- good filling properties able to hide small substrate defects
- ready for rolling and brushing (spraying in the commercial sector is possible by adding the thinner HP-IMC-X)
Please order the thinner separately.
Does not adhere to PE, PP, PTFE, ...
Not suitable for new polyester coatings.
Notes on processing:
For a non-slip and textured surface, we recommend applying a layer of the HP-PP-TEXTUR in the floor and stair area in addition to the complete coating with the HP-PP.The HP-PP-TEXTUR can be applied directly onto the fresh HP-PP. For an optimal bond without intermediate sanding, the last layer of the underlying coating with the top coat must not be older than 24h (at max. 20°C ambient temperature). A solid but still slightly tacky substrate is ideal. If the coating is applied after 24 hours, the entire substrate must be sanded, otherwise the adhesion may be too low.
Notes on the application procedure:
For application we recommend our polyamide-rollers HP-L1016 (width 10cm) HP-L1017 (width 15cm) and HP-L1022 (width 25cm).Frequently asked questions
Why HP-PP-TEXTUR?
A polyurethane coating can bring its advantages to bear especially under difficult conditions. The surfaces of pools and bathing ponds are ideal for this. HP-PP-TEXTUR is mainly used in stair and floor areas due to its non-slip and textured nature.
Which colours are available?
Over 190 different RAL colours can be mixed and delivered. If the pool is exposed to high levels of sunlight, we advise against using too dark colours, as there may be large differences in temperature above and below the water in the pool or pond. This could lead to strong differences in stress in the laminate and thus to cracks.
How can I apply HP-PP-TEXTUR?
By adding the thinner HP-IMC-X, the HP-PP-TEXTUR is ready to roll and brush. For application we recommend our polyamide rollers HP-L1016, HP-L-1017, HP-L-1022.
Can I apply a 2K system (resin + hardener) to an existing 1K layer?
It is generally not recommended. 2K coatings are usually much harder than 1K coatings and due to the different properties cracking and chipping can occur. In addition, the solvent contained in 2K lacquer can soften the 1K substrate and following might cause irritation of the surface. With a simple test it can be checked whether the old coating is a 1K or 2K coating: Press a cloth soaked in acetone onto the varnish for at least 1 minute. If the surface remains unchanged, it is a 2K coating. If the paint dissolves or curls after a short time, the substrate is a 1K coating and therefore unsuitable for 2K. Old 1-component coatings must therefore always be removed completely!
Resin and hardener were mixed in the bucket. How long can the system be used?
The so-called pot life is 3 - 5 hours. A very important factor is the ambient temperature. The warmer, the shorter the pot life! After 5 hours at approx. 20°C the mixture reacts and becomes viscous. After that it should not be used anymore!
Why does the colour look uneven or irregular during application?
When mixing, it is important to stir each individual component well beforehand and to mix the entire system well afterwards. After mixing, the mixture should be left to stand for approx. 10 minutes so that any bubbles that may have formed can escape.
Does it make sense to apply the paint as thick as possible?
When applying the paint, ensure that the paint is rolled up evenly and not too thick. If the layer is too thick, the entire varnish cannot react with oxygen and therefore cannot harden. This would result in blistering and an uneven colour image. Later, it can even lead to flaking. Tip: It is better to apply twice thinly than once too thick! It should be noted that the first layer should be tack-free before applying the second layer. The second layer must be applied within 24 hours (at 20°C) before the first layer hardens.
I have used much less than specified. Can I return the paint?
All varnishes are mixed on customer order and therefore unfortunately cannot be taken back. In addition, the specified quantity of approx. 150g/m² should be observed. If the paint is applied too thinly, the quality and durability of the coating will be reduced.
The time window for the subsequent coating was exceeded and the substrate has already hardened. Can I still apply the subsequent coating?
A too late application of HP-PUR-PLUS on the first layer or on the primer can lead to orange peel (a disturbance of the colour flow). Furthermore, a chemical bond between the individual layers is no longer guaranteed. Therefore, it would be necessary to sand the surface again after it has dried through and then rub it with acetone to remove dust or grease.
HP-PP-TEXTUR is too rough for me, how can I remedy this?
In this case, an additional layer of HP-PUR-PLUS on top of the HP-PUR-PLUS-TEXTUR would help. The additional layer covers the particles somewhat and thus "defuses" them. In this way, the properties of the non-slip surface can be largely designed as desired. Please note that a fully hardened layer must be sanded and cleaned with acetone.
The colour of the coating fades within a short time. What can be the reason?
The HP-PUR-PLUS has a very high resistance to chemicals and UV light. In the pool area, incorrect chlorination can cause the colour to fade. For this reason, the chlorine content and pH value should be measured regularly. The optimum value for chlorine is 0.3 - 0.6 mg/l and pH 7.0 -7.6. If these values are maintained, you can enjoy the colour stability of the PU coating for years.
Technical data 2K PUR Topcoat PLUS | HP-PP-TEXTUR
- Colouring: Upon costumer request available in almost all RAL colours
- Mixing rations: 100 parts resin / 50 parts hardener / 30 - 40 parts thinner HP-IMC-X
- Working time (pot life): ca. 6 - 8 hours (at 20°C)
- Working temperature OPTIMUM: 18 - 25 °C
- Working temperature MINIMUM: 15 °C (air); 70% relative air humidity
- Consumption: ca. 200 - 250 g/m²
- Recommended layers: 1 - 2 (dependent on colour tone and application quantity)
Hazard statements
Resin component:
Danger
H226 Flammable liquid and vapour.
H312 Harmful in contact with skin.
H315 Causes skin irritation.
H332 Harmful by inhalation.
H335 May cause respiratory irritation.
H336 May cause drowsiness and dizziness.
H411 Toxic to aquatic life with long lasting effects.
H412 Harmful to aquatic life with long lasting effects.
Hardener component:
Warning
H226 Flammable liquid and vapour.
H304 May be fatal if swallowed and enters airways.
H315 Causes skin irritation.
H317 May cause allergic skin reaction.
H319 Causes severe eye irritation.
H331 Toxic by inhalation.
H332 Harmful by inhalation.
H334 May cause allergy, asthma-like symptoms or breathing difficulties if inhaled.
H335 May cause respiratory irritation.
H336 May cause drowsiness and dizziness.
H411 Toxic to aquatic life with long lasting effects.
